450,55 kr
Produktet er for øyeblikket ikke tilgjengelig; vi varsler deg gjerne via e-post.
Vi sender deg en påminnelse
Skriv inn e-postadressen din, slik at vi kan varsle deg så snart varen er tilgjengelig igjen i ønsket størrelse.
Beskrivelse
motogadget mo.Stop, the adjustable digital brake light modulator to increase driving safety.
The standard brake light becomes an eye-catching warning light through various flashing modes. The following traffic recognizes the brake operation of the motorcycle much better and faster. An important plus in safety on all two-wheeled vehicles, which, as is well known, are quickly overlooked. Especially for custom bikes and conversions with very small or low-lying brake lights.
The principle is partly already integrated in cars with high equipment ex works (adaptive brake lights). In other countries, such as the USA, also widely used for motorcycles. Unfortunately not (yet) approved in Germany. In case of a case the mo.Stop does not have to be removed. Simple reprogramming via dip switch is sufficient.
The mo.Stop can also be used as a BLINKRELAY WITH AUTOMATIC SWITCH OFF! Security aspect! Flasher unit switches off the flasher(s) automatically after 20 seconds if the appropriate setting is made. No more accidental continuous flashing!
Use as brake light control:
- ultra small and lightweight, practically only one piece of cable with a tiny device in candy size
- Laying in the wiring harness simply in series with the brake light
- 6 different light/flash variants for brake light adjustable
- almost independent of load - therefore suitable for almost all LED brake lights (from 1 W) or conventional brake light
- super simple connection only via two cables - simply connect in series
- short-circuit proof - automatic overload protection - fuse against voltage peaks from the on-board power supply
- no heat development during operation
- also suitable for 6 V brake light
- immediate, loss-free response of the brake light - waterproof and vibration-proof
use as flasher relay (without/with switch-off):
- nearly load-independent (from 1 W)
- always constant flashing frequency
- therefore suitable for almost all LED indicators, all micro indicators, halogen indicators, 10 Watt indicators, 21 Watt indicators etc.
- ideal for custom bikes and modifications with limited space - no bulky standard relay
- works e.g. with 4 turn signals or 2 bar end turn signals etc.
- super simple connection only via two cables - easy to switch in series
- also suitable for 6 V turn signals
- adjustable as turn signal relay WITH AUTOMATIC OFF
The standard brake light becomes an eye-catching warning light through various flashing modes. The following traffic recognizes the brake operation of the motorcycle much better and faster. An important plus in safety on all two-wheeled vehicles, which, as is well known, are quickly overlooked. Especially for custom bikes and conversions with very small or low-lying brake lights.
The principle is partly already integrated in cars with high equipment ex works (adaptive brake lights). In other countries, such as the USA, also widely used for motorcycles. Unfortunately not (yet) approved in Germany. In case of a case the mo.Stop does not have to be removed. Simple reprogramming via dip switch is sufficient.
The mo.Stop can also be used as a BLINKRELAY WITH AUTOMATIC SWITCH OFF! Security aspect! Flasher unit switches off the flasher(s) automatically after 20 seconds if the appropriate setting is made. No more accidental continuous flashing!
Use as brake light control:
- ultra small and lightweight, practically only one piece of cable with a tiny device in candy size
- Laying in the wiring harness simply in series with the brake light
- 6 different light/flash variants for brake light adjustable
- almost independent of load - therefore suitable for almost all LED brake lights (from 1 W) or conventional brake light
- super simple connection only via two cables - simply connect in series
- short-circuit proof - automatic overload protection - fuse against voltage peaks from the on-board power supply
- no heat development during operation
- also suitable for 6 V brake light
- immediate, loss-free response of the brake light - waterproof and vibration-proof
use as flasher relay (without/with switch-off):
- nearly load-independent (from 1 W)
- always constant flashing frequency
- therefore suitable for almost all LED indicators, all micro indicators, halogen indicators, 10 Watt indicators, 21 Watt indicators etc.
- ideal for custom bikes and modifications with limited space - no bulky standard relay
- works e.g. with 4 turn signals or 2 bar end turn signals etc.
- super simple connection only via two cables - easy to switch in series
- also suitable for 6 V turn signals
- adjustable as turn signal relay WITH AUTOMATIC OFF
| Monteringsanvisning: | Last ned |
| Henrettelse: | Digital |
|---|